This tutorial was written by Monti on December 17th 2006. It's concept is copyrighted to Monti. Any creation you make from my ideas are yours. You may print out this tutorial for your own personal use, but please do not copy it in any way to put online, pass out or rewrite without my permission or worse yet attempt to claim as your own.
For this tutorial you will need
Paint Shop Pro
The Following Colour Chart
Save and then open in PSP
Of course you are free to use any colours you want.
Ok we are ready to start.
REMEMBER TO SAVE OFTEN
Step 1:
This is the outline we will be making. Mine has been resized a lot so you can see it clearly.
To make this easier I have numbered all pixels over 1.
We will be adding the paw pads and the face at the end.
Open a new image 100 x 100 transparent.
Select the brush tool with the following settings.
Size:1 - Hardness, Opacity and Density: 100
Zoom in to about 800% - 1000%
Set your foreground to colour 1 on the outline colour chart (#945937) and start at whichever point you prefer. I find it easier to start the highest point, in this case the top of his head. (You can move the image later using your move tool if you need to).
Do all the outline in that colour APART from the the insides of the ears and the wings.
Change your foreground to colour 3 on the outline colour chart (#F27B6B) and do the insides of his ears ouline.
Change your foreground to colour 7 on the outline colour chart (#887A8E) or a colour of your choice and do the wings ouline.
Change your foreground to colour 5 on the outline colour chart (#F3A47D) Zoom in on your image so you can see his left foot (as you look at it) properly.
Using the chart below draw in his paw pads.
Move over to the right foot and draw in his right paw pads using the chart below.
Step 2:
When your outline is complete, select your magic wand with the following settings and click inside the head.
Select colour 2 (#D48B5E) on your bear colour chart and flood fill that selection.
Keep selected.
Selections float, Effects 3D effects, Cutout with the following settings
Vertical: 0
Horizontal: 0
Opacity: 70
Blur: 14
Shadow colour: Use your bear outline.(#945937)
Make sure fill interior with colour is UNchecked.
Deselect.
Step 3:
Select your magic wand and click inside the body of the bear.
Fill with colour 2 (#D48B5E) on your bear colour chart.
Keep selected.
Selections float, Effects 3D effects, Cutout with the following settings
Vertical: 0
Horizontal: 0
Opacity: 60
Blur: 17
Shadow colour: Use your bear outline.(#945937)
Make sure fill interior with colour is UNchecked.
Deselect.
Step 4:
Select your magic wand and click inside the left leg (as you look at it) of the bear making sure to select the stray pixel shown in the screen shot below.
Fill with colour 2 (#D48B5E) on your bear colour chart.
Keep selected.
Selections float, Effects 3D effects, Cutout with the following settings
Vertical: 0
Horizontal: 0
Opacity: 60
Blur: 5
Shadow colour: Use your bear outline (#945937)
Make sure fill interior with colour is UNchecked.
Deselect.
Repeat for the right leg.
Step 5:
Select your magic wand and click inside the left outer ear (as you look at it) making sure you select all parts.
Fill with colour 2 (#D48B5E) on your bear colour chart.
Keep selected.
Selections float, Effects 3D effects, Cutout with the following settings
Vertical: 0
Horizontal: 0
Opacity: 60
Blur: 2
Shadow colour: Use your bear outline (#945937)
Make sure fill interior with colour is UNchecked.
Deselect.
Repeat for the right ear.
Step 6:
Select your magic wand and click inside the left foot (as you look at it) making sure to select the stray pixel shown in the screen shot below.
Fill with colour 2 (#D48B5E) on your bear colour chart.
Keep selected.
Selections float, Effects 3D effects, Cutout with the following settings
Vertical: 0
Horizontal: 0
Opacity: 60
Blur: 5
Shadow colour: Use your bear outline (#945937)
Make sure fill interior with colour is UNchecked.
Deselect.
Repeat for the right foot.
Step 7:
Select your magic wand and click inside all the paw pads holding down the shift key to select them all.
Fill with colour 6 (#FAd0C0) on your bear colour chart.
Keep selected.
Selections float, Effects 3D effects, Cutout with the following settings
Vertical: 0
Horizontal: 0
Opacity: 100
Blur: 2
Shadow colour: Use your paw pad outline (#f3A47D)
Make sure fill interior with colour is UNchecked.
Deselect.
Step 8:
Select your magic wand and click inside both inner ears holding down the shift key to select both.
Fill with colour 4 (#F9C3BD) on your bear colour chart.
Keep selected.
Selections float, Effects 3D effects, Cutout with the following settings
Vertical: 0
Horizontal: 0
Opacity: 75
Blur: 2
Shadow colour: Use your inner ear outline (#F27B6B)
Make sure fill interior with colour is UNchecked.
Deselect.
Step 9:
Select your magic wand and click inside the top part of the left wing (as you look at it).
Fill with colour 8 (#D5C3DD) on your bear colour chart (or a lighter shade of the colour you chose.
Keep selected.
Selections float, Effects 3D effects, Cutout with the following settings
Vertical: 0
Horizontal: 0
Opacity: 100
Blur: 5
Shadow colour: Use your wing outline
Make sure fill interior with colour is UNchecked.
DO NOT Deselect.
Go to Adjust - Add/Remove Noise
Add Noise at 6%, Uniform and Monochrome checked.
Deselect.
Repeat for the top right wing.
Select your magic wand and click inside the lower part of the left wing (as you look at it).
Fill with colour 8 (#D5C3DD) on your bear colour chart (or a lighter shade of the colour you chose.
Keep selected.
Selections float, Effects 3D effects, Cutout with the following settings
Vertical: 0
Horizontal: 0
Opacity: 100
Blur: 2
Shadow colour: Use your wing outline
Make sure fill interior with colour is UNchecked.
DO NOT Deselect.
Go to Adjust - Add/Remove Noise
Add Noise at 6%, Uniform and Monochrome checked.
Deselect.
Repeat for the lower right wing.
Step 10:
Now we are going to draw in his face, so zoom in close on the face.
Add a new raster layer a draw in his face using the chart below.
You will need to use the colour black and colour 5 (#F3A47D) on your bear colour chart.
Select your magic wand and click inside the muzzle.
Fill with colour 6 (#FAd0C0) on your bear colour chart. Keep selected.
Selections float, Effects 3D effects, Cutout with the following settings
Vertical: 0
Horizontal: 0
Opacity: 100
Blur: 3
Shadow colour: Use your muzzle outline (#F3A47D)
Make sure fill interior with colour is UNchecked.
Deselect.
Merge all visible and save as a png.
No comments:
Post a Comment